The importance of protonation and tautomerization in relative binding affinity prediction: a comparison of AMBER TI and Schrödinger FEP

In drug discovery, protonation states and tautomerization are easily overlooked. Through a Merck–Rutgers collaboration, this paper re-examined the initial settings and preparations for the Thermodynamic Integration (TI) calculation in AMBER Free-Energy Workflows, demonstrating the value of careful consideration of ligand protonation and tautomer state. Finally, promising results comparing AMBER TI and Schrödinger FEP+ are shown that should encourage others to explore the value of TI in routine Structure-based Drug Design.     

Effect of branched alkyl side chains on the performance of thin‐film transistors and photovoltaic cells fabricated with isoindigo‐based conjugated polymers

New isoindigo and di(thienyl)ethylene‐containing π‐extended conjugated polymers with different branched side chains were synthesized to investigate their physical properties and device performance in thin‐film transistors and photovoltaic cells. 11‐Butyltricosane (S3) and 11‐heptyltricosane (S6) groups were used as side‐chain moieties tethered to isoindigo units. The linking groups between the polymer backbone and bifurcation point in the branched side chain differ in the two polymers (i.e., PIDTE‐S3 and PIDTE‐S6 ). The polymers bearing S6 side chains showed much better charge transport behavior than those with S3 side chains. Thermally annealed PIDTE‐S6 film exhibited an outstanding hole mobility of 4.07 cm² V^?1 s^?1 under ambient conditions. Furthermore, bulk heterojunction organic photovoltaic cells made from a blend film of PIDTE‐S3 and (6,6)‐phenyl C61‐butyric acid methyl ester demonstrated promising device performance with a power conversion efficiency in the range of 4.9–5.0%. © 2015 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 2015 , 53, 1226–1234     

Validation of primary formaldehyde gas standards prepared by dynamic thermogravimetry through a tri-national comparison of gaseous formaldehyde amount fraction

A validation study for primary formaldehyde gas standards was performed at three National Metrology Institutes: the Korea Research Institute of Standards and Science (KRISS), the National Metrology Institute of Japan (NMIJ) and the National Institute of Metrology of China (NIM). The studied materials had a nominal amount fraction of 2 μmol/mol formaldehyde in nitrogen balance and were prepared in 10-L aluminum cylinders by KRISS. The impurities in the materials were analyzed using a gas chromatograph/atomic emission detector and a Fourier-transform infrared spectrometer (FTIR). The stability of the materials was assessed for 1 year by KRISS using paraformaldehyde as a source for the primary standard gas and a cavity ring-down spectrometer (CRDS) instrument as the measurement method. The amount fraction of formaldehyde in the materials decreased linearly by 0.74 % each month. The studied materials that exhibited similar linear rates of decline were distributed to the participants. After the measurement was completed by the participants, the materials were returned to KRISS and the stability analysis based on the primary standard maintained at KRISS was repeated. NMIJ analyzed the materials using paraformaldehyde as the source of the primary standard of formaldehyde and FTIR analysis, whereas NIM used trioxane as the primary standard gas source and CRDS analysis. The results of the comparison revealed good agreement between the results and were within the expanded uncertainty of 2 % although each of them used different combinations of methods in the generation of primary gas standards and measurements.     

Monolayer Co3O4 Inverse Opals as Multifunctional Sensors for Volatile Organic Compounds

Monolayers of periodic porous Co₃O₄ inverse opal (IO) thin films for gas‐sensor applications were prepared by transferring cobalt‐solution‐dipped polystyrene (PS) monolayers onto sensor substrates and subsequent removal of the PS template by heat treatment. Monolayer Co₃O₄ IO thin films having periodic pores (d≈500 nm) showed a high response of 112.9 to 5 ppm C₂H₅OH at 200 °C with low cross‐responses to other interfering gases. Moreover, the selective detection of xylene and methyl benzenes (xylene+toluene) could be achieved simply by tuning the sensor temperature to 250 and 275 °C, respectively, so that multiple gases can be detected with a single chemiresistor. Unprecedentedly high ethanol response and temperature‐modulated control of selectivity with respect to ethanol, xylene, and methyl benzenes were attributed to the highly chemiresistive IO nanoarchitecture and to the tuned catalytic promotion of different gas‐sensing reactions, respectively. These well‐ordered porous nanostructures could have potential in the field of high‐performance gas sensors based on p‐type oxide semiconductors.     

Evaluation of alumina slurry dispersion by nuclear magnetic resonance relaxation as a comparison to conventional dispersion evaluation methods

In this paper, we evaluated the particle dispersion degree of alumina slurry containing a dispersant by solvent nuclear magnetic resonance (NMR) relaxation and compared it with conventional dispersion evaluation methods such as viscosity, particle size, and sedimentation height measurements. The dispersion of slurry was evaluated via numerical analysis of the transverse relaxation time (T₂). The effect of the changes in different parameters of the experiment in terms of milling time, solid loading, and dispersant amount was investigated by NMR relaxation as well as conventional methods. The results of NMR relaxation measurements revealed that T₂ correlates well with other dispersion evaluation methods; thus, it is an efficient technique to evaluate the dispersion of alumina slurry, specifically, when studying the effect of the change in milling time and dispersion amount.